gears

  1. OrganicByte

    GT-3 spur gear issue?

    (Edited, issue located at closed inspection) So the original spur gear totally disintegrated this weekend. Not sure what happened but doesn’t look good. Kind of disappointing, as it was first proper run after break in. Since I need to do some major work on it anyway I might as well swap it out...
  2. Nadboo

    Savage flux 9t bevel gear

    Does anybody know what diff/bevel gear sets if any would replace the bulletproof diff bevel gear, the 9t gear. I can’t find hpi parts and I’m hoping by some miracle I can use a diff (high hopes) from another manufacturer. I took my flux out to entertain a kid (6yr old) a few weeks ago. After...
  3. TDA

    Savage XL Clutch and Steel Spurs

    Hello Everyone, I had a short question about the combo toot clutch and Steel Spurs. Once a "mech" of R/C had changed mine to: 16/52 It's any good or it's better to change it? Thank you in advice for any suggestions :) Cheers TDA
  4. M4tty69

    Melting spurs and stripping clutch bells

    hi all, Sorry if this has already been covered in another thread but I had a little search and couldn’t find an answer.. I have two problems here. Firstly I shall say that my savage x 4.6 is only used for bashing and it takes quite a beating so I expect to break things but this is getting a...
  5. D

    Spur gear stripped

    Good a Afternoon everyone. As the title says my clutch bell got distroyed today. I have a savage x ss. I stripped 2 spurs before the clutch bell stripped. I checked all screws, they were tight. I pulled the engine to make sure the engine plate wasn’t broke or bent. Engine plate looked...
  6. A

    Savage x spur question

    I am replacing my spur and looking at the Manuel and it’s confusing first my new plastic spur looks like it needs a bushing or bearing the old one is very stuck in the old spur but the manual doesn’t show it then I watched an hpi video and it shows a black plastic washer and I don’t see that in...
  7. S

    Parts for second gear

    Hey everyone, So this is my first post here, but I have been lurking around thus fourm for years now, I have had an issue with my savage x for quite some time now, just been too lazy to fix it! Long story short I only have second gear as I'm missing the little adjuster pin and spring/ ball...
  8. H

    savage x 3 speed conversion help!

    hello bashers and thrashers. relatively new to the rc car scene, I bought my first nitro, a RTR savage x 4.6 bigblock. I have purchased a new 3 speed conversion kit and went about dismantling for the conversion, only to find that the spacer that sits between the c clip and the smallest of the 3...
  9. sticky 2gs

    quick ? savage 25

    When your replacing your spur gear should u tighten all the way or tighten than untight half turn which is more better
  10. Nihal

    Striped Spur Gear

    Did my 3rd tank today. Keep stalling about and have to restart about 7 times. I thought there was an issue with the needle setting and richen HSN out but the problem still stays. Then I richen all 3 needles ( HSN, LSN & idle ) and somehow did solve the issue. I did put 3 loops in my fuel line as...
    • Nihal
    • Thread
    • gears savage spur stripped
    • Replies: 9
    • Forum: HPI Savage
  11. Juarezd

    Stripped slipper clutch

    Hey hope ya guys can give me a hand. Today I started to break in my savage. I let it idle through 2 tanks of fuel like it said. When I got to the driving around I gave it some gas it moved foward a little bit then stopped. The motor revved up but the truck wouldn't move.took a look at the truck...
  12. Joeyeberhardt

    Metal first gear

    does anyone have the part number to replace the plastic gear with a metal one on the 3spd
  13. J

    Gearing Setup (Feedback)

    Would like to get your performance feedback from those running this setup which I plan on doing to my Savage XL: LRP. 32 / Dynamite 086 tuned pipe / Robinson Racing 48/16 gearing How was your bottom-end and top-end performance? I mostly bash and not too interested on always doing wheelies...
  14. R

    Savage wont shift into second

    Hey guys! This will be my first thread here because i am kind of new to the RC world. i have enjoyed it a lot so far but i am at a dead end and cant figure out why my savage 4.6 wont shift. I got it off of a classifieds site and traded it for a pocket bike i got for $15 and it wasn't running at...
    • Rouskie
    • Thread
    • gears savage shifting transmission
    • Replies: 19
    • Forum: HPI Savage
  15. chrome

    Gearing advice?

    I bought a bag of extra parts for my Savage, it contained a 19t clutch bell and a 51t spur gear. My Savage has a 17t clutch bell and a 47t spur gear. Would my truck be more responsive or have a better top end with which combo, or should I leave it the way it is? My truck has a LRP 28 spec 3 for...
  16. SAVYDUNBROKE

    What did you do to your HPI Savage today?

    We have this as a sticky on my S-10 forum...Jus thought it would be cool to have a thread here and see where it goes since we are constantly makin mods,bashing and racing daily. Today I: Installed Venom fail-safe Batt level indicator New shock oil Fuel filter RPM wheels
  17. frddyj

    Gear Chart for Savage Flux

    Gear ratios for the Savage Flux HP using different spur and pinion gears. Gear ratio details: A Lower numbered Ratio is actually a "Higher Ratio" and = Higher Top End, Slower Acceleration. More heat generated. Why? Because the wheels turn at a higher rate the lower the ratio. Higher Top...
  18. MotoPsycho

    Gear Chart

    I'm sure this has been done already, but I thought it could use an easily searchable title for anyone interested. Gear ratios explained HIGHER GEAR ratio "number" (ex. 4.08:1) = Lower Gearing - EX. 13t cb/53t spur = 4.08:1 ratio-LOW GEARING! (High gear ratio number = great bottom end, lower...
Back
Top