Recent content by Butters

  1. Butters

    Jammin JPX 21 Pullstart conversion !!!!

    Nitrojedi, That is sweet, great work. What parts did you use to convert it? A .21 would go great in my racer this year and you have peaked my intrest!
  2. Butters

    LRP Spec 3 Parts

    Hey all, Well I was able to get a piston and sleeve. I had a race this past weekend and was to talk to the storre owner. He had a LRP on the side opened that he pulled the pullstart off of. He gave me the piston and sleeve. I still having been trying to find them online but It hard to find...
  3. Butters

    LRP Spec 3 Parts

    Hey all, After a grueling weekend of racing, I am looking into rebuilding my Spec 3. I looked around to see who carries piston and sleeves but no one does. What does bother me is that Tower state the Piston & Sleeve set is discontinued. I couldn't even find the parts on the LRP site. I have...
  4. Butters

    08' Racer

    Senitro, Yes the pipe does fit tight. To help prevent the pipe from running to much I used a heat guns the handle of a glow plug wrench to make a pocket in the side of the body. I didnt need much to allow better fitment. Check out the 4th picture down with the body on. You can see the dimple...
  5. Butters

    Why D.A. and not Isopropyl???

    Just remeber to check loctited screws!! Denatured alcohol and Simple Green will breakdown the loctite over time.
  6. Butters

    Body Sizes

    Any body for an MGT will fit the stock Savage X chassis
  7. Butters

    08' Racer

    Blazer, Yes those are FLM shock towers but I cut .25" off of the top of the to lower te mounting of the body. The LST shock set up I helped you with worked great last year but am trying something new. I used the rear shocks for an losi 8t on all four corners of the savage. If this setup...
  8. Butters

    08' Racer

    Hey all, Sorry I havne't post the build up lately but i have been tied up the development of the truck and work lately. Here are some of the final build up picks. I will post later all the I parts I used after the 18th. Currently getting the truck dialed in for Rc Madness' North East Offroad...
  9. Butters

    chassis plates

    Blazer, I am agreeing with larsen, HPI's Savage X chassis is 5mm (6.35mm = .25 in) lower than the .21 & .25 stock chassis HPI's LCG chassis is 12mm lower that the .21 & .25 chassis plates. Platium Rc Products (Larsen's) if i am correct are .500 lower compared to .21 & .25 chassis...
  10. Butters

    Plug for Losi LiPo.

    Hopit, Losi runs JR stlye connectors since most of their kits come with JR servos and plugs, try a female JR connector. Another option is to do as I did, swith your plug for deans. Chris
  11. Butters

    My new roller

    Blazer, Thanks for the props if you need anything more info on that set up spring/oil combos and effects let me know. Build is looking good!
  12. Butters

    Does your LHS support the Savage?

    My shop used to support the savage heavily, but lately it has been transitioning to more support for Losi 8 & 8t, Revo's, Associated 8. Since the shop has a track and host offroad racing, he doesn't see many savages around except for our racers. Pretty much my teammates are the only customers...
  13. Butters

    Alloy Diff Cup Bearing Wear

    Ntecn1, Acutally I wont be creating a balancing problem. If I had both parts turned individualy this I would see a problem since I don't have a datum surface to work from. The couter sink hole in the ring gear actually locate the ring to the alloy cup.Trying to pick up axis of the bolt cirlce...
  14. Butters

    Alloy Diff Cup Bearing Wear

    Hey guys, I am having my diff cups assembly turned so I can use an 8mm x 16mm bearing instead of the 10mm x 16mm. While cleaning I noticed some wear marks on the HPI alloy cup. After everything was cleaned and dried, I went and took a new bearing (10mm x 16mm) from my roomate fresh shipment...
  15. Butters

    08' Racer

    Scott, I making a second plate this week for a spare setup. Let me know at I'll make an extra for you.
See more
Back
Top