Search results

  1. gnarkill

    losi 454 vs Lrp .28 spec 3

    Well, its time for a new motor. From reading, I understand that the Lrp .28 and Losi 454 are very similar. Could someone who has ran both of them tell me which is a better motor and why? Thanks
  2. gnarkill

    f4.6 carb fix.

    I'm not sure about other motors, but in my opinion this is NOT the way to do it. If you are not familiar with it, this is what's up with it. there is a thermal heat shield on the carb neck, the part that goes into the engine block. It is pressed on, and if you twist the carb or overtighten...
  3. gnarkill

    RcDriver surprise

    Looking through rcdriver, I found one of HPISF's best. Just thought I'd post and say congrats on getting into the magazine.
  4. gnarkill

    WTB F4.6 carb pinch bolt

    I need a carb pinch bolt for a f4.6. Doesn't have to be new, shoot me a pm if you have one and what you want for it.
  5. gnarkill

    bad carb?

    My F4.6 has been acting up as usual, but this time I can't figure it out. The truck will only idle for approx. 20 seconds even with a carb gap as large as 3mm. I think the carb is bad because i noticed where the airfilter sits it is malled but the inside is fine. Also, when I let off the...
  6. gnarkill

    tank least likely to break

    I blew out my mgt tank a week or two ago with a small flip it grass. I didn't really like the tank because it was a leaky one. What tank should I use that isn't going to blow out with one flip? I've been eying the HB d8 tank and the ofna 250cc tank. Lemme know what you guys think. -thanks
  7. gnarkill

    Spektrum DX3E review

    Just got a DX3E yesterday, but I am going to put this out there, than report back later with my stand on it. This radio only has a 1 model memory so you have to change you're epa's and trims when switching vehicles. To start this radio's going price is $100, which is less than i expected it to...
  8. gnarkill

    Converting to BL/LiPo?

    I'm not ready to do it yet, but I'm tossing this idea out there see what your ideas are. I've never really been into electric and started reading a little about 2 weeks ago. My understandings are that Kv is how many rpm you will be getting out of the motor. S rating is how many cells...
  9. gnarkill

    will 43/15 work

    I have a 15 tooth hardened clutch bell, and am getting a steel spur. The final drive ratio would be 2.86 (which I think is good compared to 2.76 : 1, the stock final drive ratio) Could I mesh these two if I were to egg out my engine plate mesh adjustments? Links: spur...
  10. gnarkill

    Oddest thing ever thread

    Let's see some pics/ stories of the oddest things that you have seen, or has happened to you. Here's mine. Driving to a cousin's birthday party I saw a hot tub in the front lawn of someone's house. Couldn't stop to get a decent pic because I didn't feel like getting shot. Could you tell...
  11. gnarkill

    Carb pinch bolt

    I just sealed my carb on my motor, but don't know how tight the carb pinch bolt should be tightened? I don't want to overkill it and potentially strip out the pinch nut out(is that what it's called?). Should it be as tight as I can get it?
  12. gnarkill

    17mm hex with a larger nut.

    I ordered a set of new wheels and tires, but I really hate the 5/16 nut to take the wheel off with. Is there a set of 17mm hexes that I could use on stock X drive cups that use a large nut like the hellfire and baja do?
  13. gnarkill

    Central Jersey Bash/BMX track spots?

    I've been looking for spots to bash at for 2-3 months and have only found 1 spot, A small pit. I'm in the Monmouth county area, Near Freehold. I'm looking for a place about 30(-) mins away. Let me know what's out there. -Thanks
  14. gnarkill

    LRP vtec/xtec?

    I am looking to upgrade my mill sometime soon and I like the lrp's but I notice a difference. Towerhobbies has the motor, which is a vtec and it is 6+1 ports. Amainhobbies has the motor, which is an xtec and it has 8+1 ports. I want the xtec version of the motor because it has 8 ports, but are...
  15. gnarkill

    gnarkill's MGT mid tank

    I didn't get a chance to pick up a pair of Flm lcg tvps this weekend, so I started building on the stock X tvps. I wanted to make this thread to show how easy it could be to do a mid tank properly, and that you can do it on a low budget. MGT tank - $17 Ofna throttle linkage - $7 Radio shack...
  16. gnarkill

    What macs pipe?

    I've noticed some people running macs pipes, and wondered what size you run and if they outperform a 086 or other pipes. I was wondering if the pipe for the .19-.35 sized motor is too long or if it did not have enough backpressure for the tank. Also, do you cut the pipe, because I know with...
  17. gnarkill

    Radio box with FLM/MGT mod

    I am doing the mgt tank mod on ext lcg flm's. I see most people use a RPM box and mount it to the tvp, how far does it stick out because in pictures, it looks like it sticks out alot. I was going to use a radio shack project box, but the smallest size they had was 3x2x1 and was a little big for...
  18. gnarkill

    Flm EXT LCG tvp's

    What are some retailers of FLM EXT LCG tvp's that are reasonally priced. I can't seem to find them anywhere.
  19. gnarkill

    Sell my savage?

    No, I'm not leaving the hobby but I am looking for something real simple though, like a baja. My dad has one, had it for like 2 months and hasn't broken anything, I'm jealous. Guys that have bajas and savages what do you think? Also, what is my savage worth, it's almost stock: Hpi Polished Pipe...
  20. gnarkill

    Driveshaft seals?

    Does anyone make dogbone seals that will fit on the savage x driveshafts. That's all. -Thanks.
Back
Top