Post your tire and rim setup pics

[Scooter]

That’s funny my silver body and purple with flames are by Ziekle racing and they do top notch work!!

 

[California Savage]

Oh yes , Zielke does an great job- but as I know they closed their business ?

 

[carldav]

Got a new set of tires from Team Energy R8MT. It’s got the same diameter as the Terra Pins but these are the low profile type:

 

[olds97_lss]

Traxxas talons... while I sort out my tuning issues. Figured less rotational mass would help figure out what's going on.

 

[Savage 6768]

My unbranded ebay wheels. 160mm x 80mm

 

[olds97_lss]

My unbranded ebay wheels. 160mm x 80mm
View attachment 6783View attachment 6782

Curious how those rims hold up. They look a bit brittle, but I like the tread pattern. Aggressive, but large lugs that will hold up to skate parks, yet get good bite in grass/dirt as well.

 

[Savage 6768]

Curious how those rims hold up. They look a bit brittle, but I like the tread pattern. Aggressive, but large lugs that will hold up to skate parks, yet get good bite in grass/dirt as well.

That was my thoughts when they turned up to, there is not much give in the rims ? will see what happens when I get to launch it on some big jumps LOL

 

[Renots]

Traxxas talons... while I sort out my tuning issues. Figured less rotational mass would help figure out what's going on.

How did you get them to fit... 17mm hex?
I like the look of those wheels and tires!!

 

[olds97_lss]

How did you get them to fit... 17mm hex?
I like the look of those wheels and tires!!

I use the wide axle stubs and I modified some cheap "extenders" I got off ebay. Pretty sure I had a thread with this, but I'm not finding it at the moment... since it deals with "tires" sort of, I guess here is fine too. lol!

My flux was used and came with the silver hub extensions on it on short stub axles. They fit horribly and I replaced them with the hpi long wheel stubs and hpi 17mm hex's/flange nuts. Then I snapped an axle off at the threads, so out of a bit of desperation, I decided to try and make those hubs work, but be better supported. I cut off just enough so that where the hex pin goes would be captured by the wheel. Was a pain with just a hack saw and a dremel, but I got them all pretty close. Drilling the hole in the right spot was the hardest part, since all I have is a hand drill. I used shims to take up any extra slop. 75-80% of the hub is supported by the extended shaft. So it's far stronger than just throwing a set of hub extensions on.

This was the one I broke the threaded part off of:

On the rest, I had to drill a hole in the cap/nut so the threaded shaft could stick through a bit:

I didn't take many photo's of the ones on my X as they are the same as the ones I got for my Flux HP, just red:

Turns out, these hubs fit traxxas keyed hex's, so that was a happy accident. Usually I use an exacto to cut the little nubs off in the hex's to use them on standard flat hex hubs.

These are the hubs, or ones just like them:
https://www.ebay.com/itm/1-Set-17mm...m-Aluminum-For-1-8-HSP-RC-Car-US/382855457218

To me, it was worth $10 to experiment and I'm glad I did. No more busted cap nuts!

HPI changed them along the line. They used to be a lot thicker and more solid. Then they became much thinner and I started breaking them. I use them on my nitro revo's as well with traxxas 17mm hex's that I cut off. I used the flange nut as the traxxas hex/hubs would wear themselves out on the threads and wobble all over the place. So I'd cut them off and just use the hex with these.

I did find some stronger ones from axial, but they don't thread on as far. The threads don't start for 1-2mm into the flange. They worked ok though on the savage. I never tried on the revo's as I still have a few hpi nuts left.

HPI Z680 old - new - axial 31087:

 

[Biddie_fiddler]

@carldav can you please show me how in the world you managed to get your savage to have such a lcg!?

I'm wanting to turn mine into more a of truggy style racer and what you've shown above is EXACTLY what I had pictured in my head!

 

[jssouthtx]

Cheap china setup. Looks cool but worthless in the performance dept.

 

[carldav]

Traxxas Sledgehammers ?

 

[Goose1072]

Baja Pro-Line Bow-Tie on a Savage XXL

 

[olds97_lss]

Traxxas Sledgehammers ?

Those are a lot larger than I thought they were... didn't they kind of make those for the maxx 4s/stampede 4xs4/rustler 4x4?

 

[olds97_lss]

My unbranded ebay wheels. 160mm x 80mm
View attachment 6783View attachment 6782

I just put a set of those on my stampede 4x4. Read the reviews and seems people had issues with them on heavier/6s trucks. So far they are working well for me on it with a slash chassis and 3S.

 

[olds97_lss]

Since my photo's are dead, mine with the XL width stubs and 3.8" trenchers:

Haven't run it in over a year.

 

[mrmiro]

HPI Super Mudder tires with RPM revolver wheels. Stablemaxx offset.

 

[mrmiro]

Ofna dish wheels with 1/2" offset and losi raminator tires.

 

[mrmiro]

Proline Badlands MX38 3.8" with F-11 Black 1/2" Offset

 

[carldav]

Those are a lot larger than I thought they were... didn't they kind of make those for the maxx 4s/stampede 4xs4/rustler 4x4?

This one is from the traxxas Maxx, 5.6” tall in diameter

 

[SavageXL85]

Dboots 4s LP wheels tires

 

[Goose1072]

Pro-Line Bow-Tie

 

[Paul Williams]

My lovely car my pride and joy. . .


I use:

SWEEP TERRAIN CRUSHER BELTED TYRE ON BLACK 17MM WHEELS 1/4 OFFSET​

Like it?

 

[Paul Williams]

.

 

[Paul Williams]

.

 

[Paul Williams]

.

 

[Paul Williams]

My lovely car my pride and joy. . .


I use:

SWEEP TERRAIN CRUSHER BELTED TYRE ON BLACK 17MM WHEELS 1/4 OFFSET​

Like it?

Sorry for the repeat messages I am still getting use to using this thing. . .
Please delete the blank posts messages pls.

 

[Gazzman]

These are the rims & tyres I run on my trucks.

Truck 1 : Fastrax Eagles, 6 Spoke Black 166mm Dia 108mm Width 17mm Centres 1/2" Offset



Truck 2 : ZD Racing 6 Spoke Black 166mm Dia 108mm Width 17mm Centres 1/2" Offset



Truck 3 : ZD Racing 8477s Black 150mm Dia 77mm Width 17mm Centres 1/2" Offset


Truck 4 : ZD Racing 8744s Black 150mm Dia 77mm Width 17mm Centres 1/2" Offset


Truck 5 : ZD Racing 8744s Metalic Red 150mm Dia 77mm Width 17mm Centres 1/2" Offset


Truck 6 : ZD Racing 8744s Metalic Red 150mm Dia 77mm Width 17mm Centres 1/2" Offset


Truck 7 : HPI GT5 Chrome/GT tyres 160mmDia 87mm Width 14mm Centres Offset N/A


Truck 8 : HPI Dirtbonz Soft Compound 150mm Dia 85mm Width 14mm Centres Offset N/A


Truck 9 : Havok rims/ Terrhex tyres 150mm Dia 85mm Width 17mm Centres 1/2" Offset


These are my spare ones.

 

[Paul Williams]

Gazzman, i like the parts on your cars they look trick especially this one: Truck 6 : ZD Racing 8744s Metalic Red 150mm Dia 77mm Width 17mm Centres 1/2" Offset

 

[Paul Williams]

You should get this suspention: