Search results

  1. tinker2141

    binding rear diff

    The ones with a T6979 part number work perfect though.
  2. tinker2141

    binding rear diff

    Solved, 6906 hubs do not fit with HD dogbones.
  3. tinker2141

    frankensavage

    problem solved. XO-1 motor/MMXLX combo, stupid fast and 5-10 degrees above ambient after a whole 6s pack of high speed runs.
  4. tinker2141

    WTB Wing mount

    looking for a PRC184 wing mount.
  5. tinker2141

    binding rear diff

    Hello all, The other day I installed Integy rear hubs on my truck and put the upper screw in the center position and noticed that it was causing my rear diff to bind. I am using flux diffs in an x with the super HD drivetrain kit #100415 and after doing a little research I found 2 things weird...
  6. tinker2141

    WTB WTB Flextek A-arms

    looking to buy a set of flextek a-arms, I don't need all 4 wheels just 2 uppers and 2 lowers. -Thanks.
  7. tinker2141

    frankensavage

    Thanks for the advice, going to lhs today to pick up a few pinions today, the Baja tires are 6oz heavier than the badlandas i was running so I am assuming that adding 2 pounds to the truck plus the rotational size of the tires has affected my gearing. batteries are 50 c and were getting a little...
  8. tinker2141

    frankensavage

    I realized the pinion bit just as I left the house, 16 right now and I run short grass and street mostly however, occasionally I go to a local off-road licensing track for some serious bashing.
  9. tinker2141

    frankensavage

  10. tinker2141

    frankensavage

    Hello all, been awhile since I've been here (got out of the hobby for a bit). I have a gearing question that I believe I need an experts help with. I just completed a nitro to brushless conversion and need a little Spur/pinion advice so heres my truck. FLM LCG TVPs Alza center diff mount with a...
  11. tinker2141

    Dual Fuel Tanks Savage X

    I don't post often but this one caught my eye; pirate I have to disagree with you on one point, if the stock savage was no fun this site and all of our time spent bashing/racing/moding would not exist, the stock savage was (IMO) the birth of a whole new hobby and I am thankfull for my hours of...
  12. tinker2141

    head shimming ?

    Nope, I have a 5 year old that thought my perfectly good camera would look great in the bath! I got it figured out though thanks, it was just a matter of tightening the bolts on the head then the shims did there job. The only reason I was concerned is because of how the motor blew (snapped crank...
  13. tinker2141

    head shimming ?

    Ok bear with me, I have a 4.6 that has been down a while and now that I'm putting it back together I have a small issue, I noticed that the sleeve is recessed into the block and that the shims on my head sit on the block which would allow the sleeve to move up and down during operation, I think...
  14. tinker2141

    Savys Build

    Get it DIRTY
  15. tinker2141

    motor plate...again!

    BTW did you mean mount or mod?
  16. tinker2141

    motor plate...again!

    Thanks for the quick response. I don't have much stock left,bulkheads and bearings are about it, I have zero experience with CF never even seen a truck with it, is it that strong or are the people who use it that good?
  17. tinker2141

    motor plate...again!

    Hey all, been a while since I posted. So on to business, my savage was ****ing me off today, couldn't get a tune or a noticeable gear shift and I started digging into the problem. Turns out the tranny clutch is shot and I was tuning a 1 speed tranny, however, on tear down I noticed that my...
  18. tinker2141

    Best tool in my tool box....

    The bench I work on, heart of my shop!
  19. tinker2141

    Rant: Had it up to here with stainless hardware!

    Hex Heads, pricey but I have stripped tools on these screws, the "armor plated" ones.
  20. tinker2141

    Track Box

    Japan?military? OKI or mainland? did mine on schwab and pushing to go back its a great place if your not an idiot.
Back
Top