Flux XS lid options

[orcusomega]

Anyone know of any lids that fit well on the XS? Mine has seen better days, and I'm looking for something different... Mini Revo bodies have too short of a wheelbase, unfortunately 🙁

 

[xtremsavage]

That's a good question Bob. I was gonna start lookin around too to see what fits. I know HPI has 2 other bodies that fit it. A El Camino and Jeep Rubicon.

On a side question, how do you like the xs so far?

 

[maximusraylius]

thats a short chassis...13 inches ...something like these ones might be ok.. http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXVDF8&P=7
or this one might be sick looking .
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXWGD3&P=7

 

[xtremsavage]

thats a short chassis...13 inches ...something like these ones might be ok.. http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXVDF8&P=7
or this one might be sick looking .
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXWGD3&P=7

Those are different options, but I don't think they'll look right on the XS. I was thinkin maybe 1/10 scale bodies for on road cars might fit. The XS is actually a 1/12 scale but uses 1/10 scale electronics. I'm probably gonna end up gettin the Rubicon body when I'm in need of a new one, unless I find other options. All I can say at this point is, give it time since it's still fairly new.

 

[orcusomega]

I like it, butit is way too fast 🙂 I need to get the geering right... Even on 2S, it will spin tires till they burn off the rims, even being easy on the trigger. admitedly, I have not tried yet tuning te ESC, since I havebeen honestly bashing the crap out of it 🙂

I got it for a song - $225 used with 2 Venom lipos, two sets of tires, and a bunch of spare parts... It is one hell of a fun little truck though!

 

[xtremsavage]

I got mine used too. Already had to replace the pinion before I even ran it. I just got packs for it Mon and have ran it a few times. It is a monster, even on 2s. I got a 3s pack just to see how crazy it is. I'm runnin the stock gearing as well but gonna switch it once I get a bit more money. Along with the drive cups on the trans. I've also gotta replace the slipper pads. They were already shot once I got it. As a temp fix, I added a washer between the slipper spring and adjustment nut and just locked it down. I also pulled the Mamba Max Pro off my blitz and swapped it out for the Vapor. Wanted a more stable ESC for those 3s runs.

Now, back on the thread topic, I just got home from the hobby shop. I found some bodies that will fit the XS. The length is perfect as far as the wheel wells lining up with the wheels. But, the width is a little too much, about 1 1/2" wider than stock. Rasing the body posts up should give plenty of clearance for the tires or trimming the wells a bit more. The ones I found were for the Traxxas Stampede elec 4x4 version. The hobby shop I went to has demo vehicles that you can test drive before buyin, and the XS is one of them. I asked the guy if I could test fit one of their display bodies on it and it's a pretty close fit. The body I tested was the Jconcepts Ford Raptor body (JCI0085 <---part #). Hope this helps a bit.

And here's the thread I started on my XS.
https://www.hpisavageforum.com/forums/showthread.php?t=19070