Search results

  1. R

    De- anodizing

    Just wet and dry sand paper. Good old fashion rub down.:bigsmilie:
  2. R

    purchasing from nitro rcx

    Hey guys looking to purchase from above company. Would anyone be willing to purchase some stuff for me ill paypal money to you first. Then post on so I wouldn't get stung on customs duties. Thing is I bought a truck second hand and was told it was a savage. Turnout to be a mad beast:stressed...
  3. R

    fuel line

    Done that no end of times. Hsn 2-3 turns from closed lsn flush. Where should lsn be roughly when set?
  4. R

    fuel line

    It won't throttle fast get up to speed cuts out about 5 seconds later. Done all sorts of tuning nothing works. Should 16% hpi fuel work or is it to low? Also I got a medium glow plug is this ok rob
  5. R

    fuel line

    Was wondering if the fuel line could be to narrow inside diameter on a savage xl. At moment its 2.5 mm seems like its not getting fuel.quick enough. Done all settings hsn lsn still seems its lacking fuel if I turn hsn open any more to let more fuel in it won't run this what leads me to believe...
  6. R

    engine tune

    Is 15% fuel ok
  7. R

    engine tune

    Opposite problem now starts up.and ticks over ok adjusted the low speed needle so ticks over slower. When I rev it fast it bogs and cuts out if I rev slowly up to speed its ok for about 10 seconds then cuts out. Low speed needle is flush high speed needle is 2 turns open from the closed...
  8. R

    gear box

    Morning got my savage up and running last night new spur finally fitted. Ain't run it on park yet just tick over. Problem is when I push it backwards it seems to have a bit o tension on it not hard to push don't seem.like its going to damage any thing. Could it just need greasing up. If so do I...
  9. R

    spur gear

    Are the tooth spacing on 47 49 & 52 spur gear the same? At moment I'm running a 47/15 ratio people say it could be to loose but it seems a good mesh with the paper method. Should it be ok. Cheers
  10. R

    engine tune

    One more thing what gap should it be 1 or 2 mm in carb cheers Rob
  11. R

    engine tune

    Oh rite remember that then on way ti work now so ill rebuild spur tonight. Was scared of ripping teeth as it was first time I started it I guess if its off floor should be ok. Practiced the mesh set up last night think I got it correct on the second attempt. Sweet. Can't wait to get this one...
  12. R

    engine tune

    Thanks for reply. Took pullstart off wound cord around a couple more times. It fired up first time a lot easier ain't got batteries in so couldn't keep it reed properly. Don't panic couldn't run away from me I had the spur gear off didn't want to rip teeth. Sounded good tho first time its been...
  13. R

    engine tune

    Evening rebuilt my savage xl it has a ex 28c engine one issue I start it up it Will run full throttle when I drop rev down it cuts out. Any ideas? Also the pullstart is very slow retracting Will a clean up of the owb help with that issue? Cheers rob
  14. R

    wheel hub

    On my savage xl the wheels got the hobao hex adapters on its a large nut that holds wheel on. What would I have get / change to put it back to original set up so it uses the smaller nut. Those wheels seem easier to get hold of see. Thanks
  15. R

    steering

    Not sure what it's like moving yet got the engine out waiting on a spur gear. All screws tightened up other day and it seems better goes one way good the other way rubbish. Did I read on here to set the steering servo have the adjuster on the controller pushed to the right????? Regarding the...
  16. R

    steering

    I got the savage xl large one bought second hand to do up. The steering don't seem to move that well on the ground standing still. Took it apart there is no serve saver just 2 plastic tubes over the metal bars is this why? Cheers
  17. R

    fuel

    Hi picked up a cheap savage xl the largest one it got the ex 28 c engine what % fuel would you suggest it is a older model. Cheers
  18. R

    spur gear

    Thanks for looking was thinking of putting the normal spur on and dropping the engine a bit. Are 52 and 49 tooth spur much different in size?
  19. R

    3rd gear upgrade

    Thanks for looking. How about if I change the spur for the newer savage its a bit bigger but I could drop the engine a bit!!!!! Are 52 tooth and 49 tooth spurs different sizes in circumfrence?
  20. R

    spur gear

    Cheers for quick reply the engine says ex on one side 28 c on other. Is that a decent engine do it point to sought of hpi ? Post some pics up later cheers
Back
Top