Search results

  1. S

    Lrp 32 so

    Forgot also I broke gear on roto start allready. Screw came out and it cocked over sideways and snapped. I haven't liked that roto start from when I saw it. Put pull starter on and I'm cranking it faster with it than roto. 2 or 3 pulls and fires up. Pretty pleased with that.
  2. S

    Lrp 32 so

    Thanks for yalls help!! I've been running it a little here and there. Motors slick, just hope I didn't ruin it. Was running on gravel and flipped over. I didn't put ziptie on breather as I've been doing break in and not jumping etc. It was pretty snug without tie but it fell off and saw some...
  3. S

    Lrp 32 so

    I'll check diff cups, does have red brake pads and there's some gouges in them and chunks missing.
  4. S

    Lrp 32 so

    Got it broke in yesterday pretty much. I'm gonna be easy on it first few times I run. Thing seem crazy strong, I was barely touching trigger and instant wheelies. Allready skinned the head too uggg. Had zip tie on it but it snapped off. I was wondering about little issue. Sometimes when I roll...
  5. S

    Lrp 32 so

    I figured it out, it burred slide a tiny little bit where idle screw was so I have some 2000 grit sand paper and taking the burr off. First time in a carb so learning as I go lol
  6. S

    Lrp 32 so

    Lol, I'm tinkering with it now. I'll take screw out. Thanks for your help btw Never could get it free, just pulled carb and no matter which way i put slide in it gets tight when it hits middle of carb. I don't see any alignment pins. Do I need to get a tiny file and try to file any burrs off?
  7. S

    Lrp 32 so

    Lol, I'm tinkering with it now. I'll take screw out. Thanks for your help btw
  8. S

    Lrp 32 so

  9. S

    Lrp 32 so

    Ahh, hope I don't have issues. I was going to break in today but didn't get time. I need some help on this, tested my linkages etc a few minutes ago and carb slide won't work freely. I took linkage loose and it's in the slide not linkage. I had to turn carb around so did I screw it up? Wonder if...
  10. S

    Lrp 32 so

    Yea that's how mine was but no place to hook spring on lrp where it went on 4.6. I took linkage off 4.6 and put on lrp to get spring it. It's all mounted up, hopefully break in tomm. I know one thing I hate abt roto start is if it dies 50 yards away u have to tote drill out there or truck back...
  11. S

    Lrp 32 so

    Why you going back to pull start? I don't see this roto start working as good as stock hpi did but we'll see. I just realized when blowing out fuel tank it has a filter so that's a plus. Stock throttle arm has a slot for a return spring and a spring, no slot or spring on this one but I'm...
  12. S

    Lrp 32 so

    The roto start didn't bind when tightened down? I've read it's common issue. It's whatever stock numbers are on bell and spur. 17 47 I think. Yea I 3rd set of shoes on now and there dynamites, worn out but they did last longer than previous I tried. Well thanks for the input, was getting a...
  13. S

    Lrp 32 so

    I got a savage x about 8 months ago and basically dogged it for 6 gallons and motor pretty much trashed. It's all stock except I replaced pipe with dyn 086 and put robinson spur and bell on it. So I ordered the 32 spec 4 and it arrived yesterday. I'm going to throw this thing on and break in...
  14. S

    Rebuilding an engine. For the first timer.

    Thanks, lrp 32 back in stock so gonna get it.
  15. S

    Rebuilding an engine. For the first timer.

    My stock 4.6 has low compression now after 6 galloons, thinking about a rebuild but I don't think it's my best option. My cooling head has 3 broke fins so need that. Add piston, sleeve and bearings and I'm probably within 50 bucks of a new one. Wanting the lrp32 but there on backorder. Any other...
  16. S

    hi my savage x 4.6 engine spins without the glowplug but dosent spin with the glowplug

    I started using a battery drill, it spins my motor over faster and cranks easier.
  17. S

    Flipping over

    It's trimmed towards brakes but there not catching, I have fiber stock pads.
  18. S

    Flipping over

    I didn't know you could over tighten one. One kept falling off and I loctite all of them and tightened pretty hard. I put body back on today and it did alot better. I free rolled it with electronics on and didn't seem to bind. Squeeks seem to be from axles rubbing hubs which it's just going to...
  19. S

    Flipping over

    But if you hit wot isn't it peaked out pretty instantly? And the jumping is just weird, use to jump it hard and didn't worry because it landed good, now I'm dreding it because it does a nose dive. The body seemed to help with air time but it's so broke up I haven't used it last few days. I just...
  20. S

    Flipping over

    I've had my savage for 4 months or so with 3 gallons through it. Pretty stock except servos and exhaust. Seems I can't keep it on it's wheels when jumping anymore. Does front flip way too much. Any ideas? And off topic but I've played with 2nd gear some and can't tell much if any difference when...
Back
Top