Recent content by ttuzun

  1. T

    Throttle servo problem

    Hi everyone. The other day I turned my receiver on and realized my throttle servo is moving only 1 way. I tried out the trim theo only thing it did was to allow the servo to move that one way (brake) if its all the way towards the other side. If i leave it at neutral on the transmitter it...
  2. T

    Engine shuts off right after start

    adjusting the low speed to where it supposed to be showed a lot of promise. HOWEVER i realized i have a pretty big (big enough to fill the surrounding with fuel) air leak at the glow plug. I tried different plugs (1 totally new) with different rings. No results it leaks from the same spot...
  3. T

    Engine shuts off right after start

    bad news! It didnt work I leaned the high speed about 2.5 turns didnt work. I increased the idle for about half a turn it worked however, then the clutch would be engaged and the wheels would turn. I played with low speed didnt work however I just realized i enriched it instead of...
  4. T

    Engine shuts off right after start

    i would adjust the high speed right? (excuse my lack of knowledge) P.S. Everything is at stock settings
  5. T

    Engine shuts off right after start

    Just as in the title, thats exactly what happens. I haven't used it for more than 6 months and i remember it happening before too. If i leave the throttle at normal it shuts off i need give it some gas for it to keep on going. Thats what i used to do until the engine got warm then the idle...
  6. T

    Sleeve Stuck

    i put it back together last night and it seems to be fine. There are some oil bubbles forming around the piston (i can see it from the exhaust) but i cant do anything about that. Everything else seems fine. Thanks everybody i wont be touching the sleeve for sometime.
  7. T

    Sleeve Stuck

    its the head button with the glow plug. Yeah thats what i was thinking. I wanted to do that again last night but my cheap allen wrench got useless. So i am going to buy some proper allen wrenches today and do it again. What if it doesnt work though? even if its seated right it still leaks...
  8. T

    Piston friction

    good to now. I am slowly learning. I don't need to spend some good old cash on a new sleeve. Thanks a lot everyone!
  9. T

    Sleeve Stuck

    i put the engine back together. Sprayed some oil on it. The top plate was pretty hard to put back in. I did it eventually. However after putting the top plate, heat sink and the bolts on i realized there is an air leak. on the rotostart side of the top plate only. It looks like a pretty...
  10. T

    Sleeve Stuck

    will do i guess it was already not smart to take it apart without having any problems. Thanks a lot for the help.
  11. T

    Piston friction

    oh. good to know thanks Should it be certainly replaced? or would it cause just performance problems?
  12. T

    Sleeve Stuck

    hmmm so if i put it back together and and if it works fine. I should have no problems. (in theory) when i took the roto start out (i had to change it) i also look inside and saw some rust looking spots on the crank shaft and burn marks on the piston. I didnt know what most people meant...
  13. T

    Sleeve Stuck

    it was stuck even before. I burned close to 2 gallons its been such a long time and I am a big newbie so i might have done something wrong in the break in. it was running fine. However it sat for more than 6 months so i wanted to take it apart before running it again. It is an HPI...
  14. T

    Sleeve Stuck

    i tried putting in hot water but didnt really help i ll try oven when i get heat resistant gloves :)
  15. T

    Piston friction

    Its my second post today but they were separate subjects. When trying to take apart the engine. I also realized the piston kind of gets stuck at the apart part. There is a lot of friction and i need to apply it a good amount of force to release it, however its really smooth and friction free on...
See more
Back
Top