Recent content by kpj313

  1. kpj313

    FLM Flux pictures

    The stock servo took a crapper on me, it just stopped working and would only move a few mm either way. HPI is sending out a replacement but I have Hitec HS-645MG to through in for now. I'm just a little leery about not having any protection for the receiver like that, $90 a pop for the futaba...
  2. kpj313

    FLM Flux pictures

    Well I got it back today from Jamie at FLM and just finished putting the cen diffs in and just waiting on a RPM Receiver Box, or if anybody has any other ideas where to mount the Receiver, or a different receiver box all together LMK! Here are some more detailed pics. Edit to add close up of...
  3. kpj313

    LiPo question

    I'm on the verge of pouncing on the flux when available, but looking for advice on lipos. I have the charger being shipped already, I went with the Hyperion EOS 0606i. I was looking at the http://www.cheapbatterypacks.com/?sid=1437061&pgid=showlipos&man=ELT&cat=E35, Elite 5000mah 3S to be...
  4. kpj313

    Tower Hobbies !!!!! ( slow)

    I live in CT and the average time for Tower is 5 days or more. If I go through Amain hobbies and it hasn't been more than 2 days, all the way from the other coast. I don't order anything from Tower any more, it usually takes them 3 days just to ship...
  5. kpj313

    FLM LCG extened TVP roll cage?

    Just about finished with my new Savage SS build with FLM LCG TVP's and was wondering what others are using for roll cages with FLM? I'm so used to the New era roll cage on my other savage X (this thing will take a beating!) but don't know if it will fit the FLM TVP's. Any Ideas? -Karl
  6. kpj313

    Shock question

    Thanks Judge, thats what I thought but didn't quite state how much to top it off in the instructions. -Karl
  7. kpj313

    Shock question

    Got my new Savage X SS yesterday and just got to building the shocks. How much do you fill the shocks with oil before you cap them :dunno: -Karl
  8. kpj313

    CEN moc question

    Is there any way to fit the cen gears in a nova cup? Also could I run one stock diff and one with the CEN mod? Or do they have to be the same due to the gearing? :dunno: -Karl
  9. kpj313

    Servo twitch

    Thanks for the reply Jason, what's the deal with the clutch rattle? What do I look for when I get in there? I put the weights in the outer holes for better contact, that wouldn't be it would it, I didn't think I had any play on the shaft either... -Karl
  10. kpj313

    Servo twitch

    I seem to be having some servo twitch going on, sometimes it will go WOT. I installed a new Hitec HS-645MG servo for steering. I've heard loose springs and other things can cause servo twitch, but I don't see anything out strange. One thing I do hear is a rattling sound from the clutch bell...
  11. kpj313

    Stering servo problems

    Yup, that is what it was. I never noticed the two switches right near the back of the radio, thought for sure it was something on the the truck itself. Thanks again. -Karl
  12. kpj313

    Stering servo problems

    Thanks for the quick response, it's the stock HPI radio. I'll take a look see after dinner and look for this switch you speak of.
  13. kpj313

    Stering servo problems

    Hello, new member here. I've been lurking a while, just haven't posted. Picked up a used savage x and just finished upgrading the linkage and steering servo to a Hitec HS-645MG. Got every thing back together and when I go to steer left it goes right and vice versa. I have my friends savage...
See more
Back
Top