Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Need to know specifically what engine you have. HPI had a 4 or 5 they put in various savage's, maybe more.
Sorry, meant a picture of the engine itself. Off the truck would be best, but at least try to angle the camera to show the side plate of the engine and another to show the top of the engine.
Kind of looks like the grey head one, nitrostar F4.6:
http://www.hpiracing.com/en/part/111595
Should be able to figure out the parts you need there. Guessing you just need the pull starter as the roto on that uses a OWB.
Unless you have the center mounted roto start vs the one off the the side:
http://www.hpiracing.com/en/parts/111595/opt
The center one uses a different starter shaft in the engine that has a flat spot on it and doesn't use a OWB. If that's what you have, then you will need the proper starter shaft from the first link without the flat spot, the OWB (one way bearing) and the starter housing.
Struggling to get a pic of the side plate this is from the top of the engine.Sorry, meant a picture of the engine itself. Off the truck would be best, but at least try to angle the camera to show the side plate of the engine and another to show the top of the engine.
Kind of looks like the grey head one, nitrostar F4.6:
http://www.hpiracing.com/en/part/111595
Should be able to figure out the parts you need there. Guessing you just need the pull starter as the roto on that uses a OWB.
Unless you have the center mounted roto start vs the one off the the side:
http://www.hpiracing.com/en/parts/111595/opt
The center one uses a different starter shaft in the engine that has a flat spot on it and doesn't use a OWB. If that's what you have, then you will need the proper starter shaft from the first link without the flat spot, the OWB (one way bearing) and the starter housing.
Cheers I have been having a look and I was thinking it’s the f4.6 like you said. Another one the link states r5 cold glow plug but I thought r5 medium was the one to run?That makes it look more like this one from amain:
https://www.amainhobbies.com/hpi-nitro-star-f4.6-monster-truck-engine-w-pullstart-hpi1495/p66381
Which looks darker on hpi's site:
http://www.hpiracing.com/en/part/1495
Yh I was thinking the 4.6 thanksThat makes it look more like this one from amain:
https://www.amainhobbies.com/hpi-nitro-star-f4.6-monster-truck-engine-w-pullstart-hpi1495/p66381
Which looks darker on hpi's site:
http://www.hpiracing.com/en/part/1495
cheers bud hats best to run 20% or 25% thanksIf your running 20% nitro, probably the medium. If higher nitro, the cold may work better.
Sorry again mate to pester you I have the back end of the savage of as looking to replace the rotor start with a pull and there is no marking of what actual engine it is I know we thought 4.6 is there a way to be entirely sure?If your running 20% nitro, probably the medium. If higher nitro, the cold may work better.
Ok bud cheers I’m thinking of getting the big block now to be fair the f 5.9I don't know. Just looks like the Nitrostar F4.6 to me.
Which looking at the chart on HPI's site would use these:
https://www.hpiracing.com/en/part/120277 (replaced discontinued part)
https://www.hpiracing.com/en/part/107829 (replaced discontinued part)
https://www.hpiracing.com/en/part/1433
https://www.hpiracing.com/en/part/1432
Welcome to HPISavageForum, a friendly forum to discuss the Savage RC Truck.
Your voice is missing! You will need to register to get access to the following site features:We hope to see you as a part of our community soon!