Search results

  1. savagechiken

    not doing wheelies anymore

    Crash thanks for the tip on the glow plug wrench, it did the trick. Tried as hard as I could to push the flywheel down onto the collet more, it didn't really do much and there are no more threads to screw the pilot nut down on so I think the gap is supposed to be like that. Reassembled the...
  2. savagechiken

    not doing wheelies anymore

    Allan, when I had my F4.6 there was a smaller gap like yours, but with this K4.6 that is as far as I could get the nut to tighten down the flywheel. I think I need an extended socket or somthing to really get in there and tighten it down. I had a hell of a time trying to tighten that nut. I...
  3. savagechiken

    not doing wheelies anymore

    I am 100% certain that the position of the cb has remained in the set position the entire time while running it, I tightened the mesh after the second spur stripped but that did not seem to help at all. The problem with the clutch not engaging and sending power to the wheels started to occur...
  4. savagechiken

    not doing wheelies anymore

    good news, u don't need them its my camera thats fuzzy LOL, but seriously the important part of the video is the sound
  5. savagechiken

    not doing wheelies anymore

    Allan Q, of course I loctite my engine screws, thanks for trying but that is not the issue here. This is a video of me moving my flywheel, the black line on it represents bdc, is it normal for that much noise to come from moving the piston? And some more pics, one showing how the...
  6. savagechiken

    not doing wheelies anymore

    Here are some pics.....
  7. savagechiken

    not doing wheelies anymore

    Alright I will get pics
  8. savagechiken

    not doing wheelies anymore

    The shoes all spring back just fine. Just noticed inside the cb there is very thin line of dirt or somthin, really stuck on but just a thin line in the center of the cb wall that goes all the way around. Could this stop the shoes from engaging the cb?
  9. savagechiken

    not doing wheelies anymore

    If they were seized wouldn't it mean my wheels would be turning? Isn't my problem that its not engaging. I cannot see any damage on on the shoes.
  10. savagechiken

    not doing wheelies anymore

    The engine has almost a gallon through it. When I turn the spur with the engine off I can move the tires a little bit at a time by turning the spur gear. How do I know if my clutches seized?
  11. savagechiken

    not doing wheelies anymore

    Took it out today after replacing the spur and tightening the cb/sg mesh. Did not notice much difference, got a couple wheelies. Then I go to start the truck and the engine is running, but the wheels are not moving. I can rev it up and spin the cb/sg, but no power is being transfered to the...
  12. savagechiken

    not doing wheelies anymore

    Edited: Actually nevermind, it is not really slipping, the spur gets locks into the clutch bell and won't move a rotation if the clutch bell is held still.
  13. savagechiken

    not doing wheelies anymore

    When I hold the clutch bell, the spur only moves about 1mm back and forth and won't rotate anymore without slipping. Is this too tight?
  14. savagechiken

    not doing wheelies anymore

    The mesh seemed fine, could it have just been the amount of throttle I was giving it at certain times such as right before landing? What is perfect cb/sg mesh? How do I know I have it?
  15. savagechiken

    not doing wheelies anymore

    Update! Good news is I got some wheelies today after re-tuning it and tightened the slipper clutch with no backing off. Also put more slack/length in the fuel line and put the shock screws in the highest hole on the shock tower. There was no signs of exhaust leak or anything. I think it will...
  16. savagechiken

    To Much Fuel Line?

    I think I may have run into a problem of having too short a line, like 6 inches with inline filter, basically as short as you can go. Can your fuel line be too short?
  17. savagechiken

    not doing wheelies anymore

    Ok, I tightened the slipper and did not make much difference so I tried tuning it and had a very hard time improving my off the line power, it just kept bogging down too much or going too lean. Got a couple wheelies but not consistently, I could not find a happy spot. So I am thinking that...
  18. savagechiken

    ventalation holes in Maximizers?

    Shanty, thanks for pointing that info out to me. I won't drill the rims, but I can't afford to risk destroying one of my zombies by botching a punch job. Instead, I will test out the hole punched tire trick with the left over stock setup. The warlocks already have holes in them so it...
  19. savagechiken

    ventalation holes in Maximizers?

    Do I really have to drill holes in my new Maximizers? Because I really don't see the need for it. I have already mounted zombies w/tape on the inside and firm molded foams and they are working great so far. They do not seem too "bouncy" to me. And I have been jumping with them too. Besides, why...
  20. savagechiken

    not doing wheelies anymore

    I think you might be on to something because last time I ran it was shifting into second so early that I could barely hear it shift. I just assumed it was because I was on grass. Luckily there was no damage to the spur gear and I didn't know that a loose slipper clutch makes the truck run in...
Back
Top