Search results

  1. MrSnuggles

    metal brakes

    i did the same using a circuit board but it didnt last long enough ended up cutting down real brake pads from a sports car with metal inlaid didnt have any problem after that even added a third metal brake disk still after getting the savage xl with the red fiber disks i have found...
  2. MrSnuggles

    slipper mod for bigger engines

    some minor changes
  3. MrSnuggles

    slipper mod for bigger engines

    here you go http://www.youtube.com/watch?v=nZi1RyGdr_s
  4. MrSnuggles

    slipper mod for bigger engines

    well i got the truck for some reason he threw in smaller motor than i asked for neu 1515 1y 2500watt and 3s and 2s LiPo for a 5s setup
  5. MrSnuggles

    free throttle/brake mod no parts needed

    i know isnt it great:beforeme: go tell others lol you gotta love the awesome stopping power you get for free with this mod now your servo can send all its power to the brakes
  6. MrSnuggles

    F4.6 Carb on K4.6?

    i just know the one fom f4.1 wont fit as it has smaller neck but if you have the f4.6 carb then you should just try it out carb from sts 30 should fit and from wasp .28 but I'm not sure if these carbs would be a good idea i think you should just get a new carb for k4.6 as that one should...
  7. MrSnuggles

    F4.6 Carb on K4.6?

    just take a rubber sticky tape and glue over the midrange needle as you wont be messing with it anyway just make sure it is flush with the carb body before any extremely sticky tape should do it holds the needle so it wont move on its own and also seals it so it will be sealed
  8. MrSnuggles

    the best equiped toolbox ever

    i have always run the savage pipes to the side as it does not leave souch a mess on the car running it straight down both makes a oil mess on the truck and aso as it blows into the ground it will blow all the dust thats on the ground so it goes in the air and sets in the oil that is on the...
  9. MrSnuggles

    the best equiped toolbox ever

    its still in the works i have a new nipple that screws in but have yet to install it and i will add holes for cooling before running the toolbox lol
  10. MrSnuggles

    the best equiped toolbox ever

  11. MrSnuggles

    slipper mod for bigger engines

    i told him not to worry about scratches just TEST IT GOOOOD hammer time :chainkiller:
  12. MrSnuggles

    slipper mod for bigger engines

    i will be checking all these things before i start it up but he told me that he would do a full testing before shipping it to me so i probably should not worry too much
  13. MrSnuggles

    slipper mod for bigger engines

    how is the warranty for these things the mmm? and btw your truck looks amazing showoff lol as I'm not sure if i can get bec anytime soon would i be best off then using a hump pack for my rx and disconnect the red wire from the esc? it causes allot of problems living in iceland when...
  14. MrSnuggles

    slipper mod for bigger engines

    what setup are you going to be running? LiPo? motor?
  15. MrSnuggles

    slipper mod for bigger engines

    lol i was confusing the mmm with the hydra 240 HV witch is rated for 50Volts i was reading about those at the same time and got them mixed up in my mind can you show me a post where this reconnection is shown so i wont be making any mistakes?
  16. MrSnuggles

    Reinforcing X rollcage

    here is another really simple one i can stand ontop of my truck without my shoe touching the engine head
  17. MrSnuggles

    my tripple disk brakes

    works great for me but these steel disks require the use of a skidplate as the most common way of deforming them is by hitting a rock or something and i totally agree with everybody they are rubbish out of the bag as the glue on pads and using steel pad between the disks what were...
  18. MrSnuggles

    slipper mod for bigger engines

    i guess ill be mix matching how i run the lipos series or parallel it has the 200Amp mamba monster max v2
  19. MrSnuggles

    slipper mod for bigger engines

    I'm buying it rtr from finedesignrc but he is putting in a larger motor than they usually use 4.7 electric hp 2x 5s LiPo neu1521 motor 3500 watts+ all types of pinions for the motor he has :10: :10: :10: :10: :10: :10: :10: if i remember right the hpi 5.9 has been dynoed at 1.8 hp
  20. MrSnuggles

    my tripple disk brakes

    yeah in my case when i had just got the truck i went through this motor plate bent problem after bad landing then i upgraded to the ss plate and tossed the cut out beams that were under it and threw in solid ones from the 3.5 savage then i put on second roll hoop over the motor (i run...
Back
Top