Search results

  1. Shanty

    Cant really wheelie anymore help

    In the video they have a bad lean case. You may just not have as bad of case. What I would do is put the needles at factory settings. I can't seem to find them online for the .25 motor. If you know them then thats what I would do. If you don't know them. I have a feeling you Low Speed is a...
  2. Shanty

    Front wheel drive only

    If you shim them correctly the stock diffs can last a long time. There is a thread somewhere on here about shimming your diffs. Just make sure you are not landing on throttle on jumps.
  3. Shanty

    Cant really wheelie anymore help

    When the high speed is lean it will do either a lean bog or completely die. A lean bog I would describe as the following. The RPM's would be high then suddenly drop the go high again. Here is a good video that describe it. http://www.youtube.com/watch?v=BJFsJAxNoRg
  4. Shanty

    Backplate one way bearing

    Like people have said it sounds like your One way bearing is slipping. This can be due to it actually broken or because it's got some oil on it and it's slipping. If it is the first time the bearing is slipping chances are it's just slipping and you can use some nitro car cleaner or something...
  5. Shanty

    upgraged engine for Savage X?

    I ran an LRP with stock tank and it worked awesome. Every person vehicle is different so there is going to be different experiences with it. Motors I would look at. LRP .28 Picco .28 Axial .28 (Almost identical to Savage 4.6 motor. It's cheaper then the rest but is an all around good motor...
  6. Shanty

    Cant really wheelie anymore help

    There is a couple things you might want check. - Make sure the slipper pad on the spur gear is ok. Yes is should slip some. But the spur might have loosened just a bit to much. After you are done checking to make sure the pad is ok, tighten it down all the way and back it off 1/8th to 1/4th of...
  7. Shanty

    LiPo Chargers???

    To be honest with you I am not sure if it would work or not. I would think as long as the current doesn't have to go the dead power supply it could work.
  8. Shanty

    beginner buggy/truggy???

    Get a 8ight or 8ight-T 1.0. They can be found very cheap on ebay now that the new 2.0 are out.
  9. Shanty

    Any Suggestions?

    I am running the same setup frddyl is. It is an awesome combo. Only thing I can recommend doing is putting packing tape with the little strings of I believe fiberglass on the inside of the tires to cut down on ballooning.
  10. Shanty

    LiPo Chargers???

    I am running the Thunder Power TP-610C and it is working great. I also know of at least 8 other people running the same charger at our track and they are all working great. For power supply I am running the following one: http://cloudclimberhobbies.com/store/product/2557/OFN92135/ The prices...
  11. Shanty

    Oil Gas ratio

    I am running 25:1 of Honda Pro Synthetic HP2. Working great so far.
  12. Shanty

    basher diff oil opinions!

    Right now I am running 30k in the front and 15k in the rear. I have it setup where I basically just steer the truck and the rear follows. I have also ran 10k in both front and rear and like that also. Heavier weight oil in the front will make the truck steer like on rail and go where it's...
  13. Shanty

    wheel studs

    Sorry to bring up an older topic but like what was said those are pretty pricey. I got 400 studs from my local dirt bike shop for $20. And those are all AMA/CMA approved gold screws. It's to see that because those studs go through a lot of force and fly shrapnel is a scary site. 400 screws was...
  14. Shanty

    new tires

    I had good luck with my Zombies and thats the tire I would go with. The only downfall to them it ballooning. But packing tape with the strings (I believe it's fiberglass) in it on the inside of the tire helps that problem. Here is a link to the Losi Zombie tires to show what they look like...
  15. Shanty

    Body shells for XL

    There are actually quite a few that will fit. Go on prolineracing.com and any bodies that say LST, LST2, MGT, Genesis will fit the XL. Here is a link to prolines bodies. http://www.prolineracing.com/c-11-bodies.aspx I personally like the boulder holder. There are a few other companies for...
  16. Shanty

    LiPo question

    Great advice Larsen. The batteries that I am using for my 8ight-E 2.0 are Thunder Power 5S 5000mah Batteries. So far I have been able to charge them at a higher C rating then other batteries I have used or know people that have used. I am able to hit them at 7 Amps and not worry about them...
  17. Shanty

    Good hex driver set?

    We just got a new Dynamite driver in the shop this week and I have to say its actually a good surprise. When I got to try it out I thought it would be a hassle, but it did the job well. Here is the link: http://cloudclimberhobbies.com/store/product/2520/DYN2930/
  18. Shanty

    busted servo

    If you have $200 to spend then you can get an amazing servo for that price. I would go with a JR 8711. It has over 400oz of torque and speed is 0.16sec if I remember off the top of my head. If you want more speed go with a 9100S or 9100T. The 9100S has 180oz torque and speed is 0.06sec, and the...
  19. Shanty

    Good hex driver set?

    I have to favorite brands when it comes to hex drivers, Dynamite and Losi. These are the ones I am using in my tool box. Dynamite: http://www.dynamiterc.com/Products/Default.aspx?ProdID=DYN3080 and http://www.dynamiterc.com/Products/Default.aspx?ProdID=DYN2819 Losi...
  20. Shanty

    New digital servo

    Check to make sure you have the right servo saver horn on the Servo it self, meaning the right number of teeth. Seems to me that thats the only think off the top of my head that would do that.
Back
Top