Search results

  1. AllanQ

    f1n3sse or aj

    Aj read your pm's
  2. AllanQ

    its ljrces birthday

    Happy Birthday LJ!
  3. AllanQ

    where to find the shims in pic?

    I got the part number out of the manual. Its the same part number as the diff cup. This is the shim that goes under the pin under the bevel gear.
  4. AllanQ

    where to find the shims in pic?

    looks like you have to buy the whole diff cup to get that shim. Part #86827 Less than 10 bucks on the bay.
  5. AllanQ

    WTB Hellfire Roller

    Sorry Jud, I have an SS, but it has all the stuff you did not want. How cheap you looking to go?
  6. AllanQ

    need serious help

    start by getting your feet wet with how the forum works, proper forum etiquette, not posting stuff which has no use or does not add value to anything in the thread or forum, reading threads and using the search buttons to find an answer.
  7. AllanQ

    need serious help

    I deleted every post in here. If a member needs something, there is a wanted section to post a thread. When posting a thread on needed parts, be specific on the parts you desire. Don't need any posts that say 'stop making stupid posts". Kinda makes the member posting it also look stupid...
  8. AllanQ

    loud pipes

    Cleaned this thread up. Lets stay on topic and help the OP out and not pi$$ and moan at each other about stupid stuff.
  9. AllanQ

    Joeguam is alive & ok

    Joe... glad to hear you and the family are safe. Recovery will probably take a while, let me know if you need anything.
  10. AllanQ

    Engine Plate Failure

    Great job making your plate and threw some reps your way. Lemme know if you decide to sell any of these, would be interested in a couple of them.
  11. AllanQ

    How do i get part of this bearing off ?

    2 flat head screw drivers, one on each side of the bearing. apply even upward pressure. If that doesn't work, you re gonna need some heat.
  12. AllanQ

    Crown gear and Bevel gear binding

    This 10char
  13. AllanQ

    proline crimefighters

    Please resize the pic..
  14. AllanQ

    Engine Plate Failure

    How long have you had this piece? If you recently purchased it, HPI may warranty it, but no promises. these savages are tough as nails, but like everything else, they are not indestructable. IMO, you do not gain anything with washers under the cap heads but it also doesn't hurt to have them...
  15. AllanQ

    Have you ever seen this? *Damage*

    Just looking at it will look like nothing is wrong with it. Usually when you hit something head on like a lamp post, tree or fence is when it happens. Don't ask me how I know this cause it has never happened to me...lmao j/k
  16. AllanQ

    Have you ever seen this? *Damage*

    Only three ways that arm will pop off 1. PFM (don't believe in it) 2. pin comes out (doesnt look like that in the pic) 3. It splits at the seam and comes off. I bet if you take a screw driver into the hole and use very slight prying action, he will see the split at the seam.
  17. AllanQ

    Have you ever seen this? *Damage*

    that is common. There is a seem from the mold right there so the arms split. Mostly happens on the lower arms especially when you hit something head on.
  18. AllanQ

    Holding washers in place... or other small parts

    A tip I learned from someone was to cut about 2 3/4" pieces from the tube on a WD-40 can and put them in the holes. You slide everything over then take the tube out and put the screw in.
  19. AllanQ

    Bulletproof Diff help

    Did this setup you bought come off of a flux or something else??
  20. AllanQ

    Health warning !

    Did I miss the joke here or did I just waste my time reading most of this crap?
Back
Top