Search results

  1. Bankrupter

    Buy or don't buy?? RPM Stablemaxx wheels

    Max I said it was **not** cold out. the rims I run now would never do that at below freezing ... don't put words in my mouth! I think these rims are ***pure trash*** (for any 8th scale that gets run, not even run hard). 10th scale Id say go for it but I don't like to see guys glue up 40+ bucks in...
  2. Bankrupter

    Buy or don't buy?? RPM Stablemaxx wheels

    I honestly just ran over that stick Max. it was way above freezing thats just left over snow pack down from a good 24 inches. you can see the mud and grass in the rim the ground was a sponge... Venting the rubber is better for any tire then the rim anyways. A leather punch works best 4 holes...
  3. Bankrupter

    Buy or don't buy?? RPM Stablemaxx wheels

    RPM says to vent the rubber and not drill that rim.. that will void the warranty aswell This was my first savage ... BTW they suck ! (sorry max) http://i83.photobucket.com/albums/j314/justin11275/stock%20savage/Feb27_0006.jpg Don't worry about stripping the hex ... it will rip out b4 that...
  4. Bankrupter

    Savage 2350 Flux jumping Van

    I like that ramp on a ramp design... LOl I do like the first ramp. I need to build one like it.
  5. Bankrupter

    The wheel fell off my wagon

    Thanks for the share AJ
  6. Bankrupter

    AARRRGGGHHH no brakes AGAIN

    take pics of the disks and the pads. thats all fine
  7. Bankrupter

    AARRRGGGHHH no brakes AGAIN

    SS brakes suck for sure bud. They can have a few different failures that make them not work, but start with getting reds if you can. If you need help at that point make a thread and Ill be happy to help and even give you a mod for reds that I run on my trucks and give you more adjustment out of...
  8. Bankrupter

    axial stock or turbo head ???????????????

    they do make more power but not any your going to "see" or "feel" Id say do it if you have other motors that run turbo plugs and you keep them on hand.
  9. Bankrupter

    Bank goes Brushless with 1ST PRC FLUX XL

    why yes, I did ....
  10. Bankrupter

    flux2350 on 6s 8s and 10s wow

    quote of the day .....
  11. Bankrupter

    Bank goes Brushless with 1ST PRC FLUX XL

    Nitro came off the shelf yesterday. should be 100% for tomorrow and I just ran all my lipos past the hyperions... few more days and the flux will be back up. the D8 is sitting looking at me funny but give her a bump and she should fire. 8T is missing a motor and the ese blitz was terrorizing the...
  12. Bankrupter

    28 and 32 Engine Specs

    Brando I think Spec I S is the normal 28 or the HPI K4.6 the RR did put out more but was a headache in its first version. had QC issues...
  13. Bankrupter

    Shims and 30% nitro?

    Sounds like my old picco ... I had to close and lean the LSN till it would do both. it was near .5 when I was done.
  14. Bankrupter

    Shims and 30% nitro?

    Just leave it a lil fat and don't worry about it. Get her run in and happy. Its going to take a good gal b4 shes not going to spike temps and be unhappy so take your time. Just be careful with -=HOT=- plugs. Not so much concern with med and colds
  15. Bankrupter

    Tekin RSpro 17.5 System QnA

    300 for you
  16. Bankrupter

    Shims and 30% nitro?

    I didnt change shims for run in and I even took one out after she was well worn in for more jam on 30%. The recommendation from OFNA is to protect the motor. Its sound advice if you don't know what detonation sounds like. I can tune and know what is good and bad for the motor so never had a...
  17. Bankrupter

    SS Dirt Bonz

    I run the ofna yellows in my Dirtbonz also. But like fred said above....
  18. Bankrupter

    ERCM Small Block Pipe Testing

    Those are sexy robin. Just put the prototype BB pipe back on the novarossi... hope to run it soon
  19. Bankrupter

    28 and 32 Engine Specs

    Maximum RPM - 39000 RPM lol do they know how high that is for a .28 ... I love MFGR specs always good for a giggle
  20. Bankrupter

    maine toys ... two new blitz's to the list

    It adds weight and bends ... But cool, I am a alloy hater... don't mind me.
Back
Top