Search results

  1. X

    listen to this savage, tell me what you think.

    my question is does this savage in the video after running WOT sounds kinda funny on the way back down the rpm band and doesn't seem right. My new axial rr is doing the same thing. I am concerned of running to lean but I know there is alot of smoke still. In the hpi tunning video when the...
  2. X

    just my thought on the axial .28 RR...

    So, bought it, dropped it in, primed, new os 8 plug. third pull and fired right up. For break in I used what the manual says, plus a beat of heat cycling mixed in. Tank #5 started to lean it out to where I was able to start shifter into second gear (new 3speed was put in at same time, i...
  3. X

    mixed thoughts on running a motor dry..

    here is my thought on whether to run your engine dry after use or not. well the only reason I hear and read on why to is.... reason not to would be, puts stress on motor untill it turns off = to running very lean. leaving a residue on moisture behind. so why do it? i see no positive...
  4. X

    new motor breaking in N maint Q's

    hey guys i just got my new mill .28RR axial. i want to know everything you guys can tell me about how to keep my engine running strong for a long time. what to do and not to do. i only got 3 gallons on my first hpi mill but i think i abused it causing a early death. what tips can u...
  5. X

    need help with clutch bell assembly on new axial rr mill

    ok so i got that first piece on and then i knowthe Nut/bolt thing goes over it, how tight does tht have to be? i can't get mt socket to grab cuz its not need enough. can i use a wrench? hw tight? does that piece witht he pins need to snug up tight?
  6. X

    jp3 pipe, fit issues?

    are you guys using stock header with this pipe because the new one fit SUPER tight... tips would be nice.
  7. X

    dual disc brake install, i have a quick question.

    i got it 99% done I just wanted to know how TIGHT should the 2 screws be that hold it all together? Snug? A bit loose? Nice and tight? PLZ help.
  8. X

    what exactly does ofna throttle mod do?

    I am still a bit unsure of the resault of this mod and how important it really is. Is stock linkage crap?
  9. X

    Need advice with full savage build.

    First off I have a stock savage that I am going to keep stock for a bit more but planning to do a full basher buildup. I do hae a hitec steering servo already though and the heavy dogbones. I have many questions I am hoping you guys can shed some light on aswell as what the progress of my...
  10. X

    wierd.. engine not holding idle..

    Ok, I dunno if its outside temps or a fuel issue where there is not enough or flooding. But basically what is happening is: i prime - then crank it over - it will start normally right away. If i try to give any gas soon after it dies. barely will crawl even an inch then die out. do I...
  11. X

    who knew.

    ok so i see one of my stock shock cap is blown open and oil everywhere... I tear down a bit of the truck to do a clean and repair the shock, next thing I know the other 7 shocks that LOOK to be fine are quite the opposite. 6 of the remaining shock have loose caps and no oil or very little...
  12. X

    tips on buying a new engine.

    I know nothing about whats good vs whats not, pretty new to the hobbie. can you pros suggest some good motors that is under the $180.00 range? its for bashing primarly.
  13. X

    how to pick out new wheelz and tirez?

    how do I choose whats right for me and my truck? Is it what ever i like? Is there a right and wrong size/tread? can u guys suggest some setups? I know stock hub is 17mm if that helps. Difference between foams? I am a basher aswell so bes setup for bashing is what I want...
Back
Top